Ford 2011 Escape v.3 Uživatelský manuál

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Message center 20Entertainment Systems 28AM/FM stereo with CD/MP3 28Auxiliary

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

CHILDPROOF DOOR LOCKSWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thechi

The IKT allows you to:• remotely unlock the vehicledoors.• remotely lock all the vehicledoors.• remotely open the power liftgateglass.• activate the p

Locking the doors1. Pressand release to lock all the doors. Assuming all vehicle doorsand the liftgate are properly closed, the parking lamps will ill

To replace the battery:1. Twist a thin coin in the slot of theIKT near the key ring in order toremove the battery cover.Note: Do not wipe off any grea

The illuminated entry system will turn off the lights if:• the ignition is turned to the on position, or• the integrated keyhead transmitter lock cont

2. Within five seconds press the 1 • 2 on the keypad. The doors will lockand then unlock to confirm that the system is in programming mode.3. Enter yo

To unlock all doors and liftgate, press the 3 • 4 control within fiveseconds of entering the factory set 5-digit code or your personal code.To lock al

Anti-theft indicatorThe anti-theft indicator is located in the instrument panel cluster.• When the ignition is in the offposition, the indicator will

Replacement of integrated keyhead transmitters (IKT) and codedkeysNote: Your vehicle comes equipped with two integrated keyheadtransmitters (IKTs). Th

Please read and understand theentire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition.2. Turn the igniti

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

FRONT SEATSWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the eve

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting the front manual seat (if eq

Adjusting the front power seat (if equipped)WARNING: Never adjust the driver’s seat or seatback when thevehicle is moving.WARNING: Do not pile cargo h

Press to raise or lower the frontportion of the seat cushion.Press to raise or lower the rearportion of the seat cushion.Press the control to move the

Note: Do not do the following:• Place heavy objects on the seat• Operate the seat heater if water or any other liquid is spilled on theseat. Allow the

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Press and ho

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Folding down second row seats1. Remove

WARNING LIGHTS AND CHIMESBase instrument cluster shown in standard measure. Metricsimilar.Optional instrument cluster shown in standard measure. Metri

Attach the safety belt web snapbutton to the quarter trim panelsnap button. This will ensure thatsafety belt does not get caught bystaying out of the

Returning the second row seats to upright position1. Pull seatback up and into uprightposition making sure seatback locksinto place and the red seatun

To remove the second row cushion1. Lift the yellow tab to release thehinges.2. Pull the cushion to the outboardside of the vehicle.To install the seco

• “Passenger airbag off” or “pass airbag off” indicator lamp• Front crash severity sensor.• Restraints Control Module (RCM) with impact and safing sen

Driver’s seat position sensorThe driver’s seat position sensor allows your Personal Safety System totailor the deployment level of the driver dual-sta

Front safety belt usage sensorsThe front safety belt usage sensors detect whether or not the driver andfront outboard passenger safety belts are faste

If any of these things happen, even intermittently, have the PersonalSafety System serviced at an authorized dealer immediately. Unlessserviced, the s

WARNING: When possible, all children 12 years old and undershould be properly restrained in a rear seating position.WARNING: Safety belts and seats ca

Pregnant women should alwayswear their safety belt. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips

When to use the automatic locking modeThis mode should be used any time a child safety seat, except abooster, is installed in passenger front or rear

Many lights will illuminate when you start your vehicle to make sure thebulbs work. If any light remains on after starting the vehicle, refer to there

Safety belt height adjustmentYour vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shoulder b

Safety belt extension assemblyIf the safety belt is too short when fully extended,a9inch(23cm)or12 inch (31 cm) safety belt extension assembly can be

The Belt-Minder威 feature uses information from the front passengersensing system to determine if a front seat passenger is present andtherefore potent

If... Then...The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately1 minute while the vehicle istraveling at least 3 mph(5 km

Reasons given... Consider...⬙Traffic is light⬙ Nearly 1 of 2 deaths occur insingle-vehicle crashes, many whenno other vehicles are around.⬙Belts wrink

The driver and front passenger Belt-Minder威 features can bedeactivated/activated by performing the following procedure:Before following the procedure,

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

WARNING: Never place your arm over the airbag module as adeploying airbag can result in serious arm fractures or otherinjuries.To properly position yo

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

Brake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the on

The RCM (restraints control module) monitors its own internal circuitsand the supplemental airbag electrical system wiring (including theimpact sensor

The front passenger sensing systemuses a ⬙passenger airbag off⬙ or⬙pass airbag off⬙ indicator which willilluminate and stay lit to remind youthat the

• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LampPasseng

ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase,

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi

A difficulty with the system is indicated by one or more of the following:• The readiness light will eitherflash or stay lit.• The readiness light wil

How does the side airbag system work?The design and development of theside airbag system includedrecommended testing proceduresthat were developed by

WARNING: Several airbag system components get hot afterinflation. Do not touch them after inflation.WARNING: If the sideairbag has deployed, theairbag

Safety Canopy姞 SystemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a deploying

How does the Safety Canopy姞 System work?The design and development of theSafety Canopy system includedrecommended testing proceduresthat were develope

Charging system: Illuminates whenthe battery is not charging properly.If it stays on while the engine isrunning, there may be a malfunctionwith the ch

The Safety Canopy is mounted to roof side-rail sheet metal, behind theheadliner, above the first and second row seats. The Safety Canopy isdesigned to

• The readiness light will not illuminate immediately after ignition isturned on.• A series of five beeps will be heard. The tone pattern will repeatp

SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle.If the child is the proper height, age, and weigh

Installing child safety seats with combination lap and shoulderbeltsThe rear seat head restraints must be removed when using a childseat that utilizes

1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear

Speed control: Illuminates whenthe speed control is engaged. Turnsoff when the speed control systemis disengaged.Overdrive cancel and gradeassist: Ill

9. Attach the tether strap (if thechild seat is equipped). Refer toAttaching child safety seats withtether straps later in this chapter.10. Before pla

Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol.The LATCH anchors are locat

Use of inboard lower anchors from the outboard seating positions(center seating use)The lower anchors at the center of the second row rear seat are sp

Attaching child safety seats with tether strapsMany forward-facing child safety seats include a tether strap whichextends from the back of the child s

2. Locate the correct anchor for theselected seating position.There are three tether anchorslocated on the headliner at the rearof the vehicle.3. Clip

Child booster seatsThe belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child

Booster seats should be used until you can answer YES to ALL of thesequestions when seated without a booster seat:• Can the child sit all the way back

• High back booster seatsIf, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo

If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat may improve thisconditio

For proper care of soiled safety belts, refer to Interior in the Cleaningchapter.WARNING: Failure to inspect and if necessary replace thesafety belt a

Parking brake on chime: Sounds when the parking brake is left on andthe vehicle is driven. If the warning stays on after the park brake is off,contact

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

VEHICLE CHARACTERISTICS4WD system (if equipped)Your vehicle may be equipped with a four-wheel drive (4WD) system.With the 4WD option, power will be de

• Narrower – to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUVs and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

Glossary of tire terminology• Tire label: A label showing the OE (Original Equipment) tire sizes,recommended inflation pressure and the maximum weight

INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air

The cold inflation pressure should never be set lower than therecommended pressure on the Safety Compliance Certification Label orTire Label.When weat

TIRE CAREInspecting your tires and wheel valve stemsPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones

WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressur

WARNING: Only use replacement tires and wheels that are thesame size, load index, speed rating and type (such as P-metricversus LT-metric or all-seaso

Optional instrument cluster shown in standard measure. Metricsimilar.Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge:

It is recommended that the two front tires or two rear tires generally bereplaced as a pair.The tire pressure sensors mounted in the wheels (originall

vehicle seems to pull to one side when you’re driving, the wheels may beout of alignment. Have an authorized dealer check the wheel alignmentperiodica

Note: Your vehicle may be equipped with a dissimilar spare tire/wheel. Adissimilar spare tire/wheel is defined as a spare tire and/or wheel that isdif

5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new tires to match the new wheeldiameter

8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n

Label or Tire Label which is located on the B-Pillar or the edge of thedriver’s door. The cold inflation pressure should never be set lower thanthe re

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Understanding your tire pressure monitoring system (TPMS)The tire pressure monitoring system measures pressure in your four roadtires and sends the ti

WARNING: Never remove the coolant reservoir cap while theengine is running or hot.Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel

When you believe your system is not operating properlyThe main function of the tire pressure monitoring system is to warn youwhen your tires need air.

Low tirepressurewarning lightPossiblecauseCustomer action requiredFlashing warninglightSpare tire inuseYour temporary spare tire is in use.Repair the

SNOW TIRES AND CABLESWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel

VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the

Seating and Safety Restraints 110Seating 110Safety restraints 122Airbags 136Child restraints 152Tires, Wheels and Loading 170Tire information 172Tire

Trip odometer: Registers the miles (kilometers) of individual journeys.• Standard instrument cluster:Press the SELECT/RESET controlonce to switch from

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400

Follow these guidelines to ensure safe towing:• Do not tow a trailer until your vehicle has been driven at least1,000 miles (1,600 km).• Consult your

Powertrain Maximum GCWR- lb (kg)1Maximum TrailerWeight - lb (kg)22WD 2.5L w/manualtransmission5000 (2268) 1500 (680)2WD 2.5L w/automatictransmission50

If you use a rental trailer, follow the instructions that the rental agencygives to you.Do not attach safety chains to the bumper.Trailer brakesElectr

• Allow more distance for stopping with a trailer attached; anticipatestops and brake gradually.Trailer towing tips• Practice turning, stopping and ba

In case of a roadside emergency with a disabled vehicle, please refer toWrecker towing in the Roadside Emergencies chapter.These guidelines are design

STARTINGPositions of the ignition1. Off— locks the gearshift leverand allows key removal.2. Accessory— allows the electricalaccessories such as the ra

WARNING: If you smell exhaust fumes inside your vehicle, haveyour dealer inspect your vehicle immediately. Do not drive if yousmell exhaust fumes.Impo

• Make sure the gearshift is in P(Park).If starting a vehicle with a manualtransmission:• Make sure the parking brake isset.• Press and hold the clutc

Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrument Cluster chapter for more informationregarding the warning

MILES (km) TO EThis displays an estimate of approximately how far you can drive withthe fuel remaining in your tank under normal driving conditions.Re

Do not crank the engine for more than 10 seconds at a time as starterdamage may occur. If the engine fails to start, turn the key to off andwait 30 se

ENGINE BLOCK HEATER (IF EQUIPPED)An engine block heater warms the engine coolant which aids in startingand allows the heater/defroster system to respo

• Be sure that areas where the vehicle is parked are clean and clear ofall combustibles such as petroleum products, dust, rags, paper andsimilar items

Under normal operating conditions, brake dust may accumulate on thewheels. Some brake dust is inevitable as brakes wear and does notcontribute to brak

Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.ADVANCETR

WARNING: Remember that even advanced technology cannotdefy the laws of physics. It’s always possible to lose control of avehicle due to inappropriate

When AdvanceTrac威 with RSC威 performs a normal system self-check,some drivers may notice a slight movement of the brake, and/or arumble, grunting, or g

Electronic stability control (ESC)Electronic stability control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa

Switching off traction controlIf the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off the traction control features

Your vehicle must be moving to calculate instantaneous fuel economy.When your vehicle is not moving, this function shows ↓, one or no barsilluminated.

WARNING: Trailer sway control does not prevent a trailer fromswaying, it mitigates the sway from increasing once it hasoccurred. TSC cannot stop all t

STEERINGYour vehicle is equipped with an electric power-assisted steering (EPAS)system. There is no fluid reservoir to check or fill.If your vehicle l

WARNING: Loaded vehicles, with a higher center of gravity,may handle differently than unloaded vehicles. Do not overloadyour vehicle and use extra pre

2. Using a screwdriver or similartool, carefully pry out the smallBrake Transmission Shift Interlock(BTSI) cover cap located to theright of the gearsh

considered normal and will not affect function or durability of thetransmission. Over time, the adaptive learning process will fully updatetransmissio

N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D

O/D (overdrive mode) is automatically returned each time the engine isturned off.L (Low)• Provides maximum engine braking.• Will downshift to the lowe

Failure to fully press the clutch pedal to the floor may causeincreased shift efforts, prematurely wear transmissioncomponents or damage the transmiss

2. Fully apply the parking brake, hold the clutch pedal down, then shiftinto 1 (First).3. Turn the ignition off.WARNING: Do not park your vehicle in N

The RSS detects obstacles up to6 feet (1.8 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the

To reset the oil monitoring system to 100% after each oil change,perform the following:1. Press and release the SETUP button to display “OIL LIFE XXX%

REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rearview camera system locatedon the liftgate provides a videoimage, which appears in therearview mirror or on

Note: The default setting for the camera delay is off. Press the“Settings” button found on the navigation screen (if equipped) to set thecamera delay

Servicing• If the image comes on while the vehicle is not in R (Reverse), havethe camera inspected by your authorized dealer.• If the image is not cle

For best performance, the driver should drive the vehicle as parallel aspossible while passing a parking space. If driven too fast (above 18 mph[30 km

When you determine the vehicle is back far enough or you hear a solidtone from the reverse sensing system, bring the vehicle to a completestop and mov

• Exceeding a vehicle speed of 6 mph (10 km/h) during automaticsteering• Deactivating the AdvanceTrac威 system or the system has activated ona slippery

• The driver allows the vehicle to roll in the opposite direction of thetransmission (such as rolling forward when R (Reverse) gear isselected.• You m

Driving with blind spot mirrorsBefore a lane change, check themain mirror first, then check theblind spot mirror. If no vehicles arepresent in the bli

Driving off-road with truck and utility vehicles4WD vehicles are specially equipped for driving on sand, snow, mud andrough terrain and have operating

• It often may be less risky to strike small objects, such as highwayreflectors, with minor damage to your vehicle rather than attempt asudden return

LANGUAGE = ENGLISH / SPANISH / FRENCHAllows you to choose which language the message center will display in.Selectable languages are English, Spanish,

Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,

Mud and waterIf you must drive through highwater, drive slowly. Traction orbrake capability may be limited.When driving through water,determine the de

Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should

Driving on snow and ice4WD vehicles have advantages over 2WD vehicles in snow and ice butcan skid like any other vehicle.Should you start to slide whi

Ford Motor Company recommends that caution be used with any vehicleequipped with a high load or device (such as ladder racks or pickup boxcover).Failu

ROADSIDE ASSISTANCEVehicles sold in the U.S. : Getting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany off

Vehicles sold in the U.S. : Using roadside assistanceComplete the roadside assistance identification card and place it in yourwallet for quick referen

FUEL PUMP SHUT-OFF SWITCHThis device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt.After an

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Not used (spare)2 15A Brake on/off switch3 15A SYNC威 module4 30

XXX MILES TO E FUEL LEVEL LOW — Displayed as an earlyreminder of a low fuel condition.LIFTGATE / GLASS AJAR — Displayed when the liftgate or liftgateg

Fuse/RelayLocationFuse AmpRatingProtected Circuits15 10A Climate control16 15A Not used (spare)17 20A All lock motor feeds, Liftgaterelease, Liftglass

Fuse/RelayLocationFuse AmpRatingProtected Circuits41 15A Driver/passenger door lockswitches, Automatic dimmingmirror, Compass, Ambientlighting, Moon r

The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected CircuitsA 80A Midi Electronic power steering module(EPAS)B 125A

Fuse/RelayLocationFuse AmpRatingProtected Circuits14 15A* Trailer tow turn lamps15 — Not used16 40A** Cooling fan 117 40A** Cooling fan 218 20A** ABS

Fuse/RelayLocationFuse AmpRatingProtected Circuits31F — Liftgate latch relay32 — Not used33 — PCM diode34 — Start diode35 10A* Run/start, Reverse lamp

Dissimilar spare tire/wheel informationWARNING: Failure to follow these guidelines could result in anincreased risk of loss of vehicle control, injury

• All-wheel driving capability (if applicable)3. Full-size dissimilar spare without label on wheelWhen driving with the full-size dissimilar spare tir

Stopping and securing the vehicle1. Park on a level surface, set theparking brake and activate hazardflashers.2. Place gearshift lever in P (Park)(aut

5. Remove the lug wrench from thejack in order to remove the sparetire from under the vehicle.Removing the spare tire or spare tire and tether (if equ

5. Use the lug wrench to remove thelug nut from the spare tire tether.6. If not replacing the spare or flattire to the underbody storage area,raise wi

speed is 80 mph (130 km/h). Refer to MyKey™ in the Locks andSecurity chapter for more information.SPEED LIMITED TO 80 MPH — Displayed when starting th

WARNING: Do not attempt to change a tire on the side of thevehicle close to moving traffic. Pull far enough off the road toavoid the danger of being h

Before placing the jack under the vehicle, NOTE the jack locations:• FrontView shown from rear of front tire.Position the jack directly below theprotr

• RearView shown from forward of reartire. Position the jack directly belowthe stud on the rear trailing arm.3. Position the jack according to theguid

Never use the differentials as ajacking point.WARNING: To lessen therisk of personal injury, donot put any part of your bodyunder the vehicle while ch

Stowing the jack and tools• Make sure the jack is fullylowered.• Reclip the tools onto the jackmaking sure that the tools arefully contained by the cl

spare tire carrier has a built-in ratchet feature that will not allow you toovertighten. If the spare tire carrier ratchets with very little effort, t

Note: Inspect the wheel pilot holeprior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean r

Preparing your vehicleWhen the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a

1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery.2. Connect the other end of thepositive (+) cable to the

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.Note: In the illustration, the vehicle on the bottom i

CANCELLED BY ABS EVENT (if equipped) — Displayed when theactive park feature has been canceled due to the ABS system activating.Refer to Active park a

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

On 4WD vehicles, it is required that your vehicle be towed with a wheellift and dollies or flatbed equipment with all the wheels off the ground toprev

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehi

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

You are required to submit your warranty dispute to BBB AUTO LINEbefore asserting in court any rights or remedies conferred by CaliforniaCivil Code Se

You can get more information by calling BBB AUTO LINE at1-800-955-5100, or writing to:BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia

The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emission control system and may causeengine knock

Dubai, United Arab EmiratesTelephone: +971 4 3326084Toll-Free Number for the Kingdom of Saudi Arabia: 800 89717409Local Telephone Number for Kuwait: 2

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

AUDIO SYSTEMSAM/FM single CD/MP3 satellite compatible sound systemWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

• Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, sid

• Spray Motorcraft威 Engine Shampoo and Degreaser (ZC-20) on allparts that require cleaning and pressure rinse clean. In Canada, useMotorcraft威 Engine

PLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authorized dealer.• For r

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENSClean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth,

INTERIORFor fabric, carpets, cloth seats, safety belts and seats equipped with sideairbags:• Remove dust and loose dirt with a vacuum cleaner.• Remove

• Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl and plastics, or oil/petroleum-basedleathe

• Clean the surfaces using the steps outlined in the Cleaning section.• Ensure the leather is dry then apply a nickel-sized amount ofconditioner to a

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

Working with the engine on1. For vehicles equipped with an automatic transmission, set the parkingbrake and shift to P (Park). For vehicles equipped w

AM/FM Radio/ VOL (Power/Volume): Pressto turn the radio on/off. Turn theknob to increase/decrease volume.If the volume is set above a certainlevel and

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.5L I4 engine1. Engine coolant reservoir2. Engine oil filler cap3. Automatic transmission dipstick (i

3.0L V6 engine1. Engine coolant reservoir2. Air filter assembly3. Brake fluid reservoir4. Automatic transmission fluid dipstick5. Power distribution b

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

CHANGING THE WIPER BLADES1. Pull the wiper blade and armaway from the glass.2. Squeeze the locking tabs torelease the blade from the arm andpull the b

Changing rear window wiper bladeThe rear wiper arm is designed without a service position. This reducesthe risk of damage to the blade in an automatic

• 2.5L I4 engine• 3.0L V6 engine6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil level is within the lower and

• 3.0L V6 engine• If required, add engine oil to the engine. Refer to Adding engine oilin this chapter.• Do not overfill the engine with oil. Oil leve

Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils certified for gasoline engines by the

BATTERYYour vehicle is equipped with aMotorcraft威 maintenance-freebattery which normally does notrequire additional water during itslife of service.If

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

Maintenance and Specifications 288Engine compartment 290Engine oil 294Battery 298Engine coolant 300Fuel information 306Air filter(s) 322Part numbers 3

To activate the autoset feature: Press MENU repeatedly until AUTOPRESET ON/OFF appears in the display. UseSEEK/TRACK toturn AUTO PRESET ON, and either

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

• Refer to scheduled maintenance information for service intervalschedules.If the engine coolant has not been checked at the recommended interval,the

• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcoholand other liquids can cause en

Whenever coolant has been added, the coolant level in the coolantreservoir should be checked the next few times you drive the vehicle. Ifnecessary, ad

If you drive in extremely hot climates:• It is still necessary to maintain the coolant concentrationabove 40%.• NEVER decrease the coolant concentrati

When fail-safe mode is activatedYou have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be ab

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsWARNING: Do not overfill the fuel tank. The pressure in anoverfilled tank may c

• Fuels can also be harmful if absorbed through the skin. If fuel issplashed on the skin and/or clothing, promptly remove contaminatedclothing and was

WARNING: When refueling always shut the engine off andnever allow sparks or open flames near the filler neck. Neversmoke while refueling. Fuel vapor i

Easy Fuel™ “no cap” fuel systemYour fuel tank is equipped with an Easy Fuel™ “no cap” fuel fillersystem. This allows you to simply open the fuel fille

/ Play/Pause: Press toplay/pause a track when playing aCD.SEEK/TRACK: PressSEEK/TRACK to access theprevious/next track.CAT (Category) / FOLD (Folder):

Flex fuel vehicle (FFV) fuel fill inletIf your vehicle is flex fuel capable, it will have a yellow bezel placed overthe fuel fill inlet.Choosing the r

It is best not to alternate repeatedly between gasoline and E85. If you doswitch fuels, it is recommended that you add as much fuel aspossible—at leas

Running out of fuelAvoid running out of fuel because this situation may have an adverseeffect on powertrain components.If you have run out of fuel:• Y

1. Locate the white plastic funnel. Itis attached to the inside of the rearpassenger side cargo compartmentaccess door.2. Slowly insert the funnel int

Filling the tankThe advertised fuel capacity of the fuel tank on your vehicle is equal tothe rated refill capacity of the fuel tank as listed in the M

Calculation 2: Multiply liters used by 100, then divide by totalkilometers traveled.Keep a record for at least one month and record the type of drivin

• Use recommended engine oil. Refer to Maintenance productspecifications and capacities in this chapter.• Perform all regularly scheduled maintenance

If other than Ford, Motorcraft威 or Ford-authorized parts are used formaintenance replacements or for service of components affectingemission control,

2. Poor fuel quality or water in the fuel—the engine may misfire or runpoorly.3. The fuel fill inlet may not have been properly closed. See Easy Fuel™

The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not

SHUFFLE: Press SHUFFLE to switch on/off and begin/stop random play.The system will only shuffle the disc currently playing.Satellite Radio (if equippe

TRANSMISSION FLUIDChecking automatic transmission fluid (if equipped)Refer to your scheduled maintenance information for scheduledintervals for fluid

The transmission fluid should be inthe zone, identified by the arrow inthis figure, if at normal operatingtemperature 185°F-200°F(85°C-93°C).High flui

Checking transmission fluid level for recreational flat towoperationBefore recreational flat towing your vehicle, the transmission fluid levelmay need

WARNING: To reduce the risk of vehicle damage and/orpersonal burn injuries do not start your engine with the aircleaner removed and do not remove it w

VEHICLE STORAGEIf you plan on storing your vehicle for an extended period of time(30 days or more), refer to the following maintenance recommendations

Note: During extended periods of vehicle storage (30 days or more),fuel may deteriorate due to oxidation. Add a quality gas stabilizerproduct to the v

• Check tire pressures and set tire inflation per the Tire Label.• Check brake pedal operation. Drive the vehicle 15 ft (4.5 meters) backand forth to

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord part name orequivalentFord part number /Ford SpecificationBrake fluid and (clutchfl

Item CapacityFord part name orequivalentFord part number /Ford SpecificationEngine oil(2.5L engine)5.3 quarts(5.0L)•Motorcraft威 SAE 5W-20Premium Synth

Item CapacityFord part name orequivalentFord part number /Ford SpecificationWindshield washer fluid Fill as requiredMotorcraft威 PremiumWindshield Wash

MEMORY PRESETS (0–9): Thereare 30 available presets, 10 each forSAT1, SAT2 and SAT3. To savesatellite channels in your memorypresets, tune to the desi

ENGINE DATAEngine 2.5L I4 Engine 3.0L V6 EngineCubic inches 152 183Required fuel Minimum 87 octane Minimum 87 octane or E85Firing order 1-3-4-2 1-4-2-

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C

Lifestyle•Ash cup/ smoker’s package •Navigation*•Cargo management accessories •Roof racks and carriers*•Cross bars •Rear bumper protector*•SUV camping

• Mobile communications systems may harm the operation of yourvehicle, particularly if they are not properly designed for automotiveuse.• To avoid int

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 30 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan3382011 Escape (204)Owners Guide, 3rd PrintingUSA (fus)

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is

• SONG SEEK MENU- Press OK to enter song seek menu.Press / to scroll through the following options:a. SAVE THIS SONG: Press OK to save the currently p

GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?This guide describes the scheduled maintenance required for yourvehicle. Carefully following

Your vehicle is very sophisticated and built with multiple complexperformance systems. Every manufacturer develops these systems usingdifferent specif

ConvenienceMany dealerships have extended evening and Saturday hours to makeyour service visit more convenient. How’s that for quality service?Factory

Check every monthEngine oil levelFunction of all interior and exterior lightsTires for wear and proper pressure, including spareWindshield washer flui

Multi-point inspection – Recommended each visitAccessory drive belt(s) Half-shaft dust boots (if equipped)Battery performance Horn operationClutch ope

Scheduled Maintenance Guide3452011 Escape (204)Owners Guide, 3rd PrintingUSA (fus)

NORMAL SCHEDULED MAINTENANCE AND LOGFor your convenience, your vehicle is equipped with a message centerwhich determines the proper oil change service

Oil Change Service Interval* 1 23456789101112131415Change engine oil and filter • ••••••••••••••Rotate tires, inspect tire wear and measuretread depth

Perform the services noted in the following table at the specifiedtime/mileage (km) period either within 3,000 miles (4,800 km) of theOIL CHANGE REQUI

Every 150,000 miles(240,000 km)Change automatic transmission fluid and filter(except 5–speed TorqShift威 transmission) (filternot required on 6F35, 6F5

• CHANNEL LOCKOUT MENU- Press OK to enter the ChannelLockout menu. Press the/ to scroll through the followingoptions:a. LOCK/UNLOCK THIS CHANNEL: Pres

Maintenance schedule logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDAT

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

SPECIAL OPERATING CONDITIONSIf you operate your vehicle primarily in one of the more demandingconditions listed below, you will need to have some item

Extensive idling and/or low-speed driving for long distances as in heavycommercial use such as delivery, taxi, patrol car or liveryAs required – Chang

Operating in dusty conditions such as unpaved or dusty roadsInspect frequently, service asrequired– Replace cabin air filter (if equipped)– Replace en

Off-road operationInspect frequently, service asrequired– Inspect steering linkage, ball joints and U-joints;lubricate if equipped with grease fitting

Special operating condition logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

EXCEPTIONSIn addition, there are several exceptions to the Normal Schedule. Theyare listed below:Normal vehicle axle maintenance❑Rear axles and power

Use SEEK/TRACK to adjust between SPEED OFF and levels1–7: Increasing the level from 1 (lowest setting) to 7 (highest setting)allows the radio volume t

ENGINE COOLANT CHANGE RECORDInitial change 6 years or 100,000 miles (160,000 km)(whichever comes first)After initial change Every 3 years or 50,000 mi

AAccessory delay ...72Active Park Assist ...232AdvanceTrac ...215Airbag supplement

Changing a tire ...254Child safety seats ...156attaching with tether straps ..163in front seat ...

coolant ...300fail-safe cooling ...304idle speed control ...298lubrication speci

Illuminated visor mirror ...67Infant seats(see Safety seats) ...156Inspection/maintenance (I/M)testing ...

Oil (see Engine oil) ...294Overdrive ...223PParental MyKey programming ...91Park Assist ...

SecuriLock passive anti-theftsystem ...106Servicing your vehicle ...288Setting the clock ...

Washer fluid ...292Water, Driving through...244Windowspower...71rear wiper/

Your vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicplayer to the in-vehic

7. Adjust the sound on your portable music player until it reaches thelevel of the FM station or CD by switching back and forth between theAUX and FM

Your vehicle may be equipped with aUSB port located on the instrumentpanel. This feature allows you toplug in media playing devices,memory sticks, and

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio forthe selectedchannel.No action required. Thisme

Radio Display Condition Action RequiredNO TEXT Categoryinformation notavailable.Category information notavailable at this time onthis channel. The sys

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1.Fan speed adjustment: Turn to select fan speed.2.RRear defroster: Press to activate/deactivat

9. Temperature control: Controls the temperature of the airflow in thevehicle.10.Passenger heated seat control (if equipped): Press toactivate/deactiv

• Do not put objects under the front seats that will interfere with theairflow to the back seats.• Remove any snow, ice or leaves from the air intake

DUAL AUTOMATIC TEMPERATURE CONTROL (IF EQUIPPED)1. AUTO/Driver temperature: Press to engage full automaticoperation. Select the desired temperature us

Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti

5. Power/ : Press to activate/deactivate the climate controlsystem. When the system is off, outside air is prevented from enteringthe vehicle through

14. Driver heated seat control (if equipped): Press toactivate/deactivate the driver heated seat. See Heated seats in theSeating and Safety Restraints

• Manual operation:1. Select MAX A/C.2. Selector .3. Select(recirculated air) to provide colder airflow.4. Set the temperature to 60°F (16°C).5. Set h

HEADLAMP CONTROLRotate the headlamp control to thefirst positionto turn on theparking lamps.Rotate to the second positiontoturn on the headlamps.Rotat

Autolamp delay system (if equipped)If your vehicle is equipped with autolamps, you can set the delay time tokeep the headlights on for up to three min

Flash-to-passPull toward you slightly to activateand release to deactivate.Daytime running lamps (DRL) (if equipped)Turns the low beam headlamps on wi

Note: If the battery is disconnected, discharged, or a new battery isinstalled, the dimmer switch requires re-calibration. Rotate the dimmerswitch fro

5. Locate the vertical adjuster onthe headlamp, then usea4mmsocket to turn the adjuster eithercounterclockwise (to adjust up) orclockwise (to adjust d

Map lamps (without moon roof)The map lamp controls (withoutmoon roof) are located on the domelamp.• Press the button on either side ofeach map lamp to

Ambient lighting (if equipped)Illuminates footwells, cupholders,the console bin and the console traywith a choice of several colors. Theambient lighti

Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance

Take your vehicle to a dealer for service if any of the above conditions ofunacceptable moisture are present.Using the right bulbsReplacement bulbs ar

Replacing headlamp bulbs1. Make sure the headlamp control is in the off position.2. Open the hood.3. Reach over the front bolster.4. Remove the bulb b

5. Carefully pull the bulb out of thesocket and push in the new bulb.6. Install the bulb socket into thelamp assembly and rotate clockwise.Replacing f

Replacing high-mount brake lamp bulbs1. Remove the two screws and movethe lamp assembly away from theliftgate.2. Remove the bulb holder from thelamp a

4. Pull bulb straight out of socketand push in the new bulb.5. Install the bulb socket into thelamp assembly and rotate clockwise.6. To install, caref

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Rear window wiper/washer controlsFor rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select:2 — Normal spe

ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamp.Slide-on-rod featureRotate the visor towards the sidewindo

Usually, when something affects the compass readings, the compass willcorrect itself after a few days of operating your vehicle in normalconditions. I

Compass calibration adjustmentPerform compass calibration in an open area free from steel structuresand high voltage lines. For optimum calibration, t

Your vehicle is not equipped with the Ford Ambulance PreparationPackage.DATA RECORDINGService Data RecordingService data recorders in your vehicle are

The tray and inside bin can beremoved to open up space to fit alaptop computer, MP3 players, CDsor handbags. To remove, open theconsole lid and pull t

To prevent the fuse from being blown, do not use the power point(s)over the vehicle capacity of 12V DC/180W. If the power point or cigarlighter socket

One-touch downAllows the driver’s window to open fully without holding the controldown. Press the switch completely down to the second detent andrelea

Note: A rear center passenger and/or raised rear center headrest (ifequipped) may also block the light from reaching the sensor.Do not clean the housi

Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re

3. Press and release SET +.4. Take your foot off the accelerator pedal.5. The indicatorlight on the instrument cluster will turn on.Note:• Vehicle spe

Turning off speed controlTo turn off the speed control, press OFF or turn off the ignition.Note: When you turn off the speed control or the ignition,

SYNC威 system hands-freecontrol feature (if equipped)Pressbriefly to use the voicecommand feature. You will hear atone and LISTENING will appear inthe

To open the moon roof: The moonroof is equipped with an automatic,one-touch, opening, closing andventing feature. Press and releasethe rear portion of

The moon roof has a sliding shade that can be opened or closed whenthe glass panel is shut. To close the shade, pull it toward the front of thevehicle

Note: EDR data is recorded by your vehicle only if a non-trivialcrash situation occurs; no data is recorded by the EDR undernormal driving conditions

Read the instructions completely before attempting to program theCar2U威 system. Because of the steps involved, it may be helpful to haveanother person

you will know which actions are time-sensitive. If you do not follow thetime-sensitive actions, the device will time out and you will have torepeat th

4. Press and release the button again. The garage door should move,confirming that programming is successful. If your garage door does notoperate, rep

Switchposition 12345678 9101112Up, onor +LLLLLLLLLLLLMiddle,neutralor 0MMMMMMMMMMMMDown,offor–RRRRRRRRRRRRL=left; M=middle; R=right3. To input these p

After successful programming, you will be able to operate your Car2U威system by pressing the button you programmed to activate the opener.The indicator

POSITIVE RETENTION FLOOR MATWARNING: Do not install additional floor mats on top of thefactory installed floor mats as they may interfere with theacce

WARNING: Make sure that the liftgate door and/or window areclosed to prevent exhaust fumes from being drawn into thevehicle. Exhaust fumes contain car

The larger, rearward, compartmentis for customer storage. To open, liftthe lid with the pull latch. The lidcan be removed to allow for flexiblestorage

To adjust the cross-bar (if equipped) position:1. Loosen the thumbwheel at bothends of the cross-bar (bothcross-bars are adjustable).2. Slide the cros

Be sure to check that the thumbwheels are tight each time load isadded, or removed from the roof rack, and periodically while traveling.Always ensure

Ford or its vendors to receive this information, do not activatethe service. Ford Motor Company and the vendors it uses toprovide you with this inform

KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unl

MYKEY™The MyKey™ feature allows you to program a restricted driving mode topromote good driving habits. All but one of the keys programmed to thevehic

2. Press and release the RESET button. HOLD RESET TO CONFIRMMYKEY will be displayed.3. Press and hold the RESET button for two seconds until MARK THIS

2. Press SETUP until PRESS RESET TO CLEAR MYKEY is displayed.3. Press and release the RESET button. HOLD RESET TO CONFIRMCLEAR is displayed.4. Press a

Note: For all vehicles, the number of MYKEY(S) PROGRAMMED orADMIN KEYS PROGRAMMED that is displayed in the MyKey™ SystemStatus menus will include the

Condition Potential CausesCannot clear MyKey™ • Key in the ignition is a MyKey™• No MyKeys™ are programmed tothe vehicle. Refer to Create aMyKey™ sect

POWER DOOR LOCKS• Press the control to unlock alldoors.• Press thecontrol to lock alldoors.Door key unlocking/lockingUnlocking the doorsTurn the key i

Note: The autolock feature can be activated/deactivated independentlyof the autounlock feature.Before following the activation or deactivation procedu

Message center procedure (if equipped)For information on activating/deactivating the autolock feature using thevehicle’s message center, refer to Mess

1. Place the key in the ignition andturn the ignition to the on position.2. Press the power door unlockcontrol on the door panel threetimes.3. Turn th