Ford 2006 E-450 v.3 Uživatelský manuál

Introduction 4Instrument Cluster 12Warning and control lights 12Gauges 16Entertainment Systems 18AM/FM stereo 18AM/FM stereo with single CD 19AM/FM st

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

VEHICLE CHARACTERISTICSHow your vehicle differs from other vehiclesSUV and trucks can differ fromsome other vehicles in a fewnoticeable ways. Your veh

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o

• Extra load: A class of P-metric or Metric tires designed to carry aheavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires].Increasing the

urged to buy a reliable tire pressure gauge, as automatic service stationgauges may be inaccurate. Ford Motor Company recommends the use ofa digital o

recommended cold pressures. A hot tire at or below recommended coldinflation pressure could be significantly under-inflated.To check the pressure in y

Tire inflation informationAll tires with Steel Carcass Plies (if equipped):This type of tire utilizes steel cords in the sidewalls. As such, theycanno

Stay out of the trajectory (1) as indicated in the illustration.TIRE CAREInspecting your tiresPeriodically inspect the tire treads for uneven or exces

Tire wearWhen the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Buil

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

built. For example, the numbers 317 mean the 31st week of 1997. After2000 the numbers go to four digits. For example, 2501 means the 25thweek of 2001.

Highway hazardsNo matter how carefully you drive there’s always the possibility that youmay eventually have a flat tire on the highway. Drive slowly t

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

SNOW TIRES AND CHAINSSnow tires must be the same size and grade as the tires youcurrently have on your vehicle.The tires on your vehicle have all weat

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).

mandatory options, no cargo (internal or external), a tongue load of10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), a

6. If your vehicle will be towing a trailer, load from your trailer will betransferred to your vehicle. Consult this manual to determine how thisreduc

Special loading instructions for owners of pickup trucks andutility-type vehiclesFor important information regarding safe operation of this typeof veh

GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoadedTrailer Weight- lb. (kg)Maximumfrontal area of

GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoadedTrailer Weight- lb. (kg)Maximumfrontal area of

GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoadedTrailer Weight- lb. (kg)Maximumfrontal area of

GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoadedTrailer Weight- lb. (kg)Maximumfrontal area of

Electronic throttle control (ifequipped): Illuminates when theengine has defaulted to a’limp-home’ operation. Report thefault to a dealer at the earli

GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoadedTrailer Weight- lb. (kg)Maximumfrontal area of

GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoadedTrailer Weight- lb. (kg)Maximumfrontal area of

GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoadedTrailer Weight- lb. (kg)Maximumfrontal area of

Your vehicle’s load capacity is designated by weight, not by volume, soyou cannot necessarily use all available space when loading a vehicle.Distribut

Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s brake system. Your vehicle may not have enoughbraking power and your chanc

Servicing after towingIf you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your scheduled maint

When backing down a ramp during boat launching or retrieval:• do not allow the static water level to rise above the bottom edge ofthe rear bumper.• do

STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo

Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,

• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).• Turn the key to 4 (ON) withoutturning the key to 5 (START).Some warning

Airbag readiness: If this light failsto illuminate when ignition is turnedto ON, continues to flash or remainson, have the system servicedimmediately

Note: If the engine does not start within five seconds on the first try,turn the key to 3 (OFF), wait 10 seconds and try again. If the engine stillfai

Refer to Brake system warninglight in the Instrument Clusterchapter for information on the brakesystem warning light.Four-wheel anti-lock brake system

Parking brakeTo set the parking brake (1), pressthe parking brake pedal down untilthe pedal stops.To release, pull the lever (2).Always set the parkin

over-spinning. When the brakes have cooled down, the system will againfunction normally. Anti-lock braking is not affected by this condition andwill f

vehicle is traveling in R (Reverse). In R (Reverse), ABS and the tractionenhancement feature will continue to function.The AdvanceTrac威 with RSC butto

• Steering feedback• The AdvanceTrac威 with RSC indicator light will flash• If your foot is on the brake pedal, you will feel a vibration in thepedal.A

TRACTION-LOK AXLE (IF EQUIPPED)This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under

The van should be operated by an experienced driver. An organizationthat owns a 15–passenger van should select one or two experienceddrivers to drive

AUTOMATIC TRANSMISSION OPERATIONBrake-shift interlockThis vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever fr

Understanding the gearshift positions of the 4–speed automatictransmissionThis vehicle is equipped with an adaptive Transmission Shift Strategy.Adapti

Check gauge: Illuminates when anyof the following conditions hasoccurred:• The engine coolant temperatureis high.• The engine oil pressure is low.• Fl

N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.(O

• Selecting 2 (Second) at higher speeds will cause the transmission todownshift to second gear at the appropriate vehicle speed.1 (First)• Provides ma

To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)Always set the parking brake full

transmission is in the D (Overdrive) position; this engine braking willslow the vehicle and assist the driver in controlling the vehicle whendescendin

Understanding the shift positions of the 5–speed automatictransmission (if equipped - diesel engines only)P (Park)This position locks the transmission

D (Drive) without OverdriveD (Drive) without Overdrive can beactivated by pressing thetransmission control switch (TCS)on the end of the gearshift lev

If your vehicle goes off the edge of the pavement• If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ea

aftermarket PTO installer since the duration of operation limit for theaftermarket PTO may be less than 10 minutes.A more complete description of PTO

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsUsing roadside assistanceComplete the roadside assi

GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera

HAZARD FLASHERThe hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is

Except for commercial strippedchassis vehicles, this switch islocated in the front passenger’sfootwell, by the kick panel.2006 Econoline (eco)Owners G

On commercial stripped chassisvehicles, this switch is located on abracket above the brake pedal.To reset the switch:1. Turn the ignition OFF.2. Check

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 5A 4–Wheel Anti–lock Brake System(4WABS) m

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description8 30A Radio capacitor(s), Ignition coil,Powertrain Control Module (PCM)diod

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description28 — Not used29 — Not used30 15A Headlamps (high beam indicator)31 10A Righ

To reduce risk of electrical shock, always replace the cover tothe Power Distribution Box before reconnecting the battery orrefilling fluid reservoirs

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription8 40A** Trailer battery charge relay9 50A** Modified vehicle power10 30A** Electric b

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription26 20A* Trailer tow turn signals27 10A* PCM28 — Not usedA — Fuel pump relayB — Horn r

Trip odometer:Registers the miles(kilometers) of individual journeys.Press the SELECT/RESET controlonce to switch from the odometer to thetrip odomete

The relays are coded as follows:Relay location Description1 Interior lamps2 Open3 Open4 Battery saverEngine compartment relay moduleThe engine compart

• hold the steering wheel firmly.• slowly move to a safe place on the side of the road.The use of tire sealants may damage your tires.Dissimilar spare

Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following:• Handling, stability and braki

Full-size Matching Spare Tire/Wheel InformationThis spare tire/wheel will match the road tire/wheel. When driving withthe full size matching spare tir

1. Park on a level surface.2. Activate the warning flashers.3. Place the gearshift in P (Park).4. Apply the parking brake and turnthe engine off.5. Bl

• the jack is located in the rearright-hand side of the cargo area.7. Use the tapered end of the lug nut wrench to unscrew wheelornaments attached by

• Never use the front or reardifferential as a jacking point.Rear axle jacking points - Allmodels except E-350 Dual RearWheel (DRW) and E-450:Rear axl

Front axle jacking points:Place the jack under the pin on thefront surface of the front axle.Do not place the jack under oron the steering linkage.• R

• 8-lug wheelNever use wheels or lugnuts different than theoriginal equipment as this coulddamage the wheel or mountingsystem. This damage could allow

5. Repeat this tightness check procedure when servicing the spare tirepressure (every six months, as per your scheduled maintenanceinformation), or at

AUDIO SYSTEMSAM/FM stereo (if equipped)1. Seek: Press/ to find thenext listenable station down/up thefrequency band.2. Tune: Press/ to manuallyadjust

When a wheel is installed, always remove any corrosion, dirt orforeign materials present on the mounting surfaces of the wheelor the surface of the wh

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level.5. Tu

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caAway

replacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure is not required prior to enforcing statecreated righ

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh

5. Power/volume: Press to turnON/OFF; turn to increase ordecrease volume levels.6. Tone: Press TONE until thedesired level — Bass, Treble, Fadeappears

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio

ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

racks, bumpers, side moldings, mirror housings or the windshield cowlarea. The paint sealant will “gray” or stain the parts over time.• Do not allow p

• Do not spray a hot engine with cold water to avoid cracking theengine block or other engine components.• Spray Motorcraft Engine Shampoo and Degreas

may cause squeaking or chatter noise from the blades, and streaking andsmearing of the windshield. To clean these items, follow these tips:• The winds

• Remove light stains and soil with Motorcraft Professional StrengthCarpet & Upholstery Cleaner (ZC-54).• If grease or tar is present on the mater

materials that meet or exceed rigid specifications. For best results, usethe following products or products of equivalent quality:Motorcraft Bug and T

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide sc

Seating and Safety Restraints 58Seating 58Safety restraints 64Airbags 74Child restraints 83Tires, Wheels and Loading 100Tire Information 102Tire Infla

1. SEEK: Press and releaseSEEK/ for previous/nextstrong station or track.2. TEXT: The filename (Fi), songtitle (So), artist text (Ar) or albumtext (AL

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENTEngine compartment component locationsRefer to the 6.0 Liter Power Stroke Direct Injection Turbo Diese

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

Replace wiper blades at least once per year for optimum performance.Poor wiper quality can be improved by cleaning the wiper blades and thewindshield,

• If the oil level is within thisrange, the oil level is acceptable.DO NOT ADD OIL.• If the oil level is below thismark, engine oil must be addedto ra

5. Fully install the engine oil filler cap by turning the filler cap clockwise1/4 of a turn until three clicks are heard or until the cap is fully sea

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How

Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lightedsubstances to come near th

7. Drive the vehicle to complete the relearning process.• The vehicle may need to be driven 10 miles (16 km) or more torelearn the idle and fuel trim

• Enables calibrated gauges to work properly.When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should

7. Select: Use with Bass, Treble,Balance, Fade and other menuselections.8. Balance: Press BAL; then pressSEL/ to shift sound to theleft/right speakers

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur

For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when

Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i

operation and the engine will run rough. Remember that the engine iscapable of completely shutting down automatically to prevent enginedamage, therefo

Automotive fuels can cause serious injury or death if misused ormishandled.Gasoline may contain benzene, which is a cancer-causing agent.Observe the f

When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke whilerefueling. Fuel vapor is extreme

2. Carefully turn the filler cap counterclockwise 1/4 of a turn until itstops.3. Pull to remove the cap from the fuel filler pipe.4. To install the ca

these additives can cause your vehicle’s emission control system todeteriorate more rapidly. In Canada, premium grade fuel generallycontains more meta

Cleaner airFord endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality.Running out of fuelAvoid running out of fuel becaus

13. FOLDER : Press to accessthe previous MP3 directory.14. FF(Fast forward): In CD/MP3mode, press until desired selectionis reached.15. REW(Rewind): I

For consistent results when filling the fuel tank:• Turn the engine/ignition switch to the off position prior to refueling,an error in the reading wil

Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin

• Adding certain accessories to your vehicle (for example bugdeflectors, rollbars/light bars, running boards, ski/luggage racks) mayreduce fuel econom

If other than Ford, Motorcraft or Ford-authorized parts are used formaintenance replacements or for service of components affectingemission control, s

3. The fuel cap may not have been securely tightened. See Fuel fillercap in this chapter.These temporary malfunctions can be corrected by filling the

POWER STEERING FLUIDCheck the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules. If adding fluid isnecess

6. If the fluid is low, add fluid in small amounts, continuously checkingthe level until it reaches the FULL COLD range. Be sure to put thedipstick ba

4. Latch the gearshift lever in P (Park) and leave the engine running.5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. Ifneces

Adjusting automatic transmission fluid levelsBefore adding any fluid, make sure the correct type is used. The type offluid used is normally indicated

Automatic transmission fluid filter (if equipped)The TorqShift automatictransmission is equipped with aserviceable external fluid filtermounted on the

labels. Ballpoint pens may damage CDs. Please contact yourauthorized dealer for further information.21. COMP(Compression): Bringssoft and loud CD pass

Changing the air filter element1. Disconnect the fresh air inlet tubefrom the radiator support.2. Open the clamp that secures thetwo halves of the air

Component14.6L V8 engine 5.4L V8 engine 6.8L V10engineOil filter FL-820-S FL-820-S FL-820-SPCV valve2Spark plugs3Automatictransmissionfilter4— FT-145

REFILL CAPACITIESFluidFord PartNameApplication CapacityBrake Fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to line onreservoir

FluidFord PartNameApplication CapacityEnginecoolant-dieselengine1Refer to the Power Stroke Direct Injection Turbo DieselOwner’s Guide Supplement.Power

FluidFord PartNameApplication CapacityFuel Tank N/A All regular andextended lengthvans and wagons35.0 gallons(132.4L)138 inchwheelbase(except E-SuperD

3Fill Dana rear axles to 1/4 inch to 9/16 inch (6 mm to 14 mm) belowbottom of fill hole. Fill Visteon axles 1/4 inch to 9/16 inch (6 mm to 14mm) below

LUBRICANT SPECIFICATIONSItem Ford partnameFord partnumberFordspecificationBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluidPM-1 ESA-

Item Ford partnameFord partnumberFordspecificationAutomatictransmission(4R70E and4R75E)1MotorcraftMERCON威VATFXT-5-QM MERCON威VAutomatictransmissionTorq

Item Ford partnameFord partnumberFordspecificationDana LimitedSlip Axles3M60 (M248)E-250/350M70FF(M267FF)E-350M70HD(M273HD)E-450SAE 90 HypoidGear OilC

MERCON威 and MERCON威 V type fluids are not interchangeable.DO NOT mix MERCON威 and MERCON威 V. Use of a transmissionfluid that indicates dual usage (MERC

Premium Satellite Compatible AM/FM Stereo In-Dash Six CD/MP3Radio (if equipped)1. SEEK: Press and releaseSEEK/ for previous/nextstrong station or trac

VEHICLE DIMENSIONSVan/wagon modelsE-150 – Inches(mm)E-250 –Inches (mm)E-350 –Inches (mm)(1) Overallheight81.2 (2062) 82.9 (2107) 84.6 (2148)(2) Trackf

Cutaway/commercial stripped chassis modelsE-350 – inches (mm) E-450 – inches (mm)(1) Overall height Refer to Body Builder for specifications.(2) Track

VEHICLE IDENTIFICATION NUMBERComplete Ford built vehiclesThe vehicle identification number is attached to your vehicle in thefollowing places:• On the

TRANSMISSION/TRANSAXLE CODE DESIGNATIONSYou can find atransmission/transaxle code on theSafety Compliance CertificationLabel. The following table tell

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford

Peace of mindRemote startVehicle security systemsFor maximum vehicle performance, keep the following information inmind when adding accessories or equ

AAccessory delay ...47AdvanceTrac ...142Air cleaner filter ...229–230Airbag supplemental

waxing ...193wheels ...194wiper blades ...195Climate con

FFail safe cooling ...213Fluid capacities ...232Four-Wheel Drive vehiclespreparing to drive yourvehicle ...

instrument panel, dimming ...35interior lamps ...37replacing bulbs ...39Lane change indicator(see Turn

3. AUX: Press to toggle between thecurrent playing media and DVD (ifequipped).4. MUTE: Press to MUTE playingmedia; press again to return toplaying med

child safety seats ...88front seats ...58Servicing your vehicle ...199Setting the clockAM/

WWarning lights (see Lights) ...12Washer fluid ...202Water, Driving through ...157Windowspower ...

252

253

254

255

256

Autoset: Press MENU until AUTOSET appears in the display. Press SELto toggle ON/OFF. Allows you to set the strongest local radio stationswithout losin

17. BAND: Press to toggle betweenAM/FM1/FM2 frequency band.18. Memory presets: To set astation: Select frequency, tune to astation, press and hold a p

CAT: CAT is only available when equipped with Satellite Radio. YourAudiophile radio comes equipped with Satellite ready capability. The kitto enable S

CD/CD player careDo:• Handle discs by their edges only. Never touch the playing surface.• Inspect discs before playing. Clean only with an approved CD

Maintenance and Specifications 199Engine compartment 201Engine oil 203Battery 206Engine Coolant 208Fuel information 214Air filter(s) 229Part numbers 2

HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature sele

To aid in side window defogging/demisting in cold weather:1. Select MIX.2. Set the temperature control to maintain comfort.3. Set the fan speed to HI.

HEADLAMP CONTROL• The first position turns on theparking, tail, license plate andside marker lamps.• The outer position turns on theheadlamps.Battery

Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the ON position,• the head

PANEL DIMMER CONTROLTo adjust the brightness of theinstrument panel, rotate the dimmercontrol clockwise/counterclockwisewhen the headlamp control is i

3. Turn on the low beam headlampsand open the hood.4. Locate the high intensity area ofthe beam pattern and place the topedge of the intensity zone ev

8.• Aerodynamic: Locate the horizontal adjuster (1) for each headlamp.Turn it clockwise or counterclockwise, to place the left edge of thehigh intensi

Third row courtesy/reading/cargo lampsThe dome portion of the lamp, thecenter light, can be turned on whenthe headlamp control is rotated fullycounter

Function Numberof bulbsTrade numberHeadlamps (sealed beam) 2 H5054Headlamps (aerodynamic) 2 9007Park lamp and turn signal(front)2 4157K or 3157KBack-u

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

4. Remove the bulb retaining ring byrotating it counterclockwise, andslide the ring off the plastic base.5. Pull the bulb straight out.Handle a haloge

3. Remove the four headlamp bulbretaining screws and the retainingring.4. Remove the headlamp.5. Disconnect the electricalconnector from the bulb and

Replacing license plate lamp bulbs1. Turn the headlamp switch to OFFand then remove the two screwsand the license plate lamp assemblyfrom the rear doo

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehicle’s overhead console will vary according toyour option package.Storage compartment (if equi

Electronic compass/temperature display (if equipped)Outside air temperatureThe outside temperature display iscontained in the overhead console.The tem

3. Press and hold the SELECTcontrol until VAR appears in thedisplay, then release. The displayshould show the current zonenumber.4. Press the SELECT c

To prevent the battery from being discharged, do not use the powerpoint longer than necessary when the engine is not running.Always keep the power poi

POWER SIDE VIEW MIRRORS (IF EQUIPPED)To adjust your mirrors:1. Selectto adjust the leftmirror orto adjust the rightmirror.2. Move the control in the d

Fold-away mirrorsThe mirrors can be manually folded forward or backwards for narrowspaces like driving through an automatic car wash or backing out of

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas

Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET ACCELcontrol until you get to thedesired sp

Turning off speed controlThere are two ways to turn off thespeed control:• Depress the brake pedal. This willnot erase your vehicle’spreviously set sp

KEYSThe key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency.You

REMOTE ENTRY SYSTEM (IF EQUIPPED)This device complies with part 15 of the FCC rules and with RS-210 ofIndustry Canada. Operation is subject to the fol

Locking the doors1. Press and release to lock all the doors.2. Pressand release again within three seconds to confirm that all thedoors are closed and

4. Insert the new battery. Refer to the diagram inside the remote entrytransmitter for the correct orientation of the battery. Press the batterydown t

7. Turn the ignition to the (3) OFF position after you have finishedprogramming all of the remote entry transmitters.8. The doors will lock, then unlo

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

Pull lever up to adjust seatback.Before returning theseatback to its originalposition, make sure that cargo orany objects are not trappedbehind the se

SPECIAL NOTICESNew Vehicle Limited WarrantyFor a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited

Press to raise or lower the rearportion of the seat cushion.Press the control to move the seatforward, backward, up or down.Quick release captains cha

Stow the tongue end of thedetachable anchor.2. Pull the seat latch handle, thenpull the seat toward the right side ofthe vehicle to disengage four pin

3. Make sure the safety belt is not twisted, then insert the seat belttongue into detachable anchor until you hear a “click” and feel the latchengage.

Stow the tongue end of thedetachable anchor (2nd row only).2. Pull the LH/RH seat latch handles(located under the seat) rearward torelease the latch h

3. Engage the LH/RH latch rod hook ends in the front striker lockingholes.4. Rotate the LH/RH latch handles forward, and at the same time slidethe sea

In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a safety belt.Each seating position in your vehicle h

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.The front outboard and rear outboard safety restraints in the vehicle arec

How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe seat belt assembly “automatic locking retractor” feature orany other seat belt function is not oper

Lap beltsAdjusting the center lap beltThe lap belt does not adjust automatically.The lap belt should fit snugly and as low as possible around thehips,

Vehicle Modification Data RecordingSome aftermarket products may cause severe engine and/or transmissiondamage; refer to the What is not covered secti

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war

If... Then...The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition...The BeltMinder威 feature will notactivate.The f

Reasons given... Consider...“I have an airbag” Airbags offer greater protection when used withsafety belts. Frontal airbags are not designed toinflate

• Step 3 must be completed within 50 seconds after the safety beltwarning light turns off.3. At a moderate speed, buckle then unbuckle the safety belt

Safety belt maintenanceInspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to ma

Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in

Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause thoseobjects to be propelled by the

How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustains alongitudinal deceleration suff

• a readiness light and tone• a diagnostic module• and the electrical wiring which connects the componentsThe diagnostic module monitors its own inter

Passenger airbag ON/OFF switch (if equipped)Note: The passenger airbag ON/OFFswitch is on vehicles with no rearseats and a gross vehicle weightrating

Notice to owners of pickup trucks and utility type vehiclesUtility vehicles have a significantly higher rollover rate thanother types of vehicles.Befo

In order to avoid inadvertent activation of the switch, alwaysremove the ignition key from the passenger air bag ON/OFFswitch.An infant in a rear-faci

If your vehicle has rear seats, always transport children who are12 and younger in the rear seat. Always use safety belts andchild restraints properly

• the child has a medical condition which, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the dr

• the child has a medical condition that, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the dri

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.Alwa

neck, the child should wear the lap and shoulder belt. Moving the childcloser to the center of the vehicle may help provide a good shoulder beltfit.Do

Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi

Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in acollision.SAFETY SEATS F

tether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. Formore info

Using your vehicle as a stationary power source (PTO)Refer to the Driving chapter for more information and guidelines foroperating a vehicle equipped

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted.6. Allo

Attaching safety seats with tether strapsChildren should be placed in the rear in an appropriate childsafety seat that is properly secured to the vehi

1. Position the child safety seat onthe front right-hand passenger seat.2. Adjust the front right-handpassenger seat full forward.3. Route the child s

5. Adjust the front right handpassenger seat to the full rearwardposition.6. Install the child safety seat tightly using the LATCH anchors or safetybe

1. Position the child safety seat onthe second row left hand or righthand bucket seat.2. Route the child safety tetherstrap over the back of the left

2. Route the child safety tetherstrap over the back of 3–Passengerbench seat.3. Clip the tether strap hook to thetether bracket mounted under rearrail

Attaching safety seats with LATCH (Lower Anchors and Tethers forChildren) attachments for child seat anchorsSome child safety seats have two rigid or

• Twelve passenger wagon• Fifteen passenger wagonrepresents LATCH anchors.represents tether strap anchors.Never attach two LATCH child safety seats to

Attach LATCH lower attachments of the child seat only to theanchors shown.If you install a child seat with rigid LATCH attachments, do not tightenthe