Ford 2009 Escape v.3 Uživatelský manuál

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Entertainment Systems 20AM/FM stereo with CD/MP3 20Auxiliary input jack (Line

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

Replacement Integrated Keyhead Transmitters (IKT) and codedkeysNote: Your vehicle comes equipped with two Integrated KeyheadTransmitters (IKTs). The I

Please read and understand theentire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition.2. Turn the igniti

FRONT SEATSNotes:WARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in t

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting the front manual seat (if eq

WARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event of a col

Press the control to move the seatforward, backward, up or down.Heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbeca

REAR SEATSHead restraintsThe purpose of these head restraints is to help limit head motion in theevent of a rear collision. To properly adjust your he

2. Place the head restraint underthe front seat for storage.3. Pull the seat release control.Note: Make sure the floor is clear of all objects before

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

Attach the safety belt web snapbutton to the quarter trim panelsnap button. This will ensure thatsafety belt does not get caught bystaying out of the

Returning the rear seats to upright position1. Pull seatback up and into uprightposition making sure seatback locksinto place and the red seatunlatche

WARNING: Remove thehead restraint stored underthe front set and return it to theoriginal position on the seatback.Failure to do so could result inpers

SAFETY RESTRAINTSPersonal Safety System姞The Personal Safety System威 provides an improved overall level offrontal crash protection to front seat occupa

longitudinal deceleration. The pretensioners are designed to activate infrontal, and in side collisions and rollovers.Driver and passenger dual-stage

WARNING: When possible, all children 12 years old and undershould be properly restrained in a rear seating position.The front passenger sensing system

Determining if the Personal Safety System姞 is operationalThe Personal Safety System威 uses a warning light in the instrumentcluster or a back-up tone t

WARNING: It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision, people riding inthese areas are more likely

Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until

(8 km/h) or more, the combination safety belts will lock to help reduceforward movement of the driver and passengers.Automatic locking modeWhen to use

WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may

How to disengage the automatic locking modeDisconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic l

The safety belt pretensioners activate during frontal collisions, and inside collisions and rollovers. A safety belt pretensioner is a device whichtig

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war

If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the onposition or less than1-2 minutes h

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...⬙Crashes are ra

Reasons given... Consider...⬙The people I’m with don’twear belts⬙Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE peop

Read Steps1-4thoroughly before proceeding with thedeactivation/activation programming procedure.The driver and front passenger Belt-Minder威 features c

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

WARNING: Never place your arm over the airbag module as adeploying airbag can result in serious arm fractures or otherinjuries.To properly position yo

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

bulbs work. If any light remains on after starting the vehicle, refer to therespective system warning light for additional information.Service engine

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

The RCM (restraints control module) monitors its own internal circuitsand the supplemental airbag electrical system wiring (including theimpact sensor

The front passenger sensing system will turn off the passenger seat sideairbag if:• the seat is empty and safety belt is unbuckled.The front passenger

• Restart the vehicle and have the person remain in this position forabout two minutes. This will allow the system to detect that personand enable the

ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase,

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi

A difficulty with the system is indicated by one or more of the following:• The readiness light will eitherflash or stay lit.• The readiness light wil

How does the side airbag system work?The design and development of theside airbag system includedrecommended testing proceduresthat were developed by

The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of

Safety Canopy姞 systemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a deploying

Brake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the on

How does the Safety Canopy姞 system work?The design and development of theSafety Canopy威 system includedrecommended testing proceduresthat were develop

designed to inflate between the side window area and occupants to furtherenhance protection provided in side impact collisions and rollover events.The

SOS Post-Crash Alert System™The SOS Post-Crash Alert automatically flashes the turn signal lamps andsounds the horn three times at four second interva

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestr

position whenever possible. If all children cannot be seated andrestrained properly in a rear seating position, properly restrain thelargest child in

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out.6. All

Charging system: Illuminates whenthe battery is not charging properly.If it stays on while the engine isrunning, there may be a malfunctionwith the ch

9. Attach the tether strap (if thechild seat is equipped). Refer toAttaching child safety seats withtether straps later in this chapter.10. Before pla

The LATCH anchors are located atthe rear section of the rear seatbetween the cushion and seatback.Follow the child seat manufacturer’sinstructions to

Use of inboard lower anchors from the outboard seating positions(center seating use)The lower anchors at the center of the second row rear seat are sp

Attaching child safety seats with tether strapsMany forward-facing child safety seats include a tether strap whichextends from the back of the child s

2. Locate the correct anchor for theselected seating position.There are three tether anchorslocated on the headliner at the rearof the vehicle.3. Clip

Child booster seatsThe belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child

When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the

Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

Move a child to a different seating location if the shoulder belt does notstay positioned on the shoulder during use.Follow all instructions provided

Overdrive cancel and gradeassist: Illuminates when theoverdrive function of thetransmission has been turned offand the grade assist function hasbeen t

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air

The cold inflation pressure should never be set lower than therecommended pressure on the Safety Compliance Certification Label orTire Label.When weat

TIRE CAREInspecting your tiresPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones, nails or glass that

WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressur

WARNING: Only use replacement tires and wheels that are thesame size, load index, speed rating and type (such as P-metricversus LT-metric or all-seaso

GAUGESStandard instrument cluster gaugesOptional instrument cluster gaugesInstrument Cluster172009 Escape (204)Owners Guide (own2002), 3rd PrintingUSA

It is recommended that the two front tires or two rear tires generally bereplaced as a pair.The tire pressure sensors mounted in the wheels (originall

Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,

To restore the full functionality of the Tire Pressure Monitoring System,have the damaged road wheel/tire repaired and remounted on yourvehicle. For a

Low TirePressureWarning LightPossiblecauseCustomer Action RequiredFlashing WarningLightSpare tire inuseYour temporary spare tire is inuse. Repair the

SNOW TIRES AND CABLESWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel

VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic

WARNING: The appropriate loading capacity of your vehicle canbe limited either by volume capacity (how much space isavailable) or by payload capacity

Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue loador king pin w

GVWR (Gross Vehicle Weight Rating) – is the maximum allowableweight of the fully loaded vehicle (including all options, equipment,passengers and cargo

GCWR (Gross Combined Weight Rating) – is the maximum allowableweight of the vehicle and the loaded trailer – including all cargo andpassengers – that

3. Subtract the combined weight of the driver and passengers from XXXkg or XXX lb.4. The resulting figure equals the available amount of cargo and lug

The above calculations also assume that the loads are positioned in yourvehicle in a manner that does not overload the Front or the Rear GrossAxle Wei

Tachometer: Indicates the enginespeed in revolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the

Do not exceed the maximum loads listed on the Safety ComplianceCertification Label. For load specification terms found on the label, referto Vehicle l

4x4GCWR (Gross Combined Weight Rating)/Trailer WeightsEngine MaximumGCWR - lb(kg)Trailer WeightRange - lb (kg)Maximumfrontal area oftrailer - ft2(m)22

HitchesDo not use hitches that clamp onto the vehicle bumper. Use a loadcarrying hitch. You must distribute the load in your trailer so that10–15% of

• Turn off the speed control. The speed control may shut offautomatically when you are towing on long, steep grades.• Consult your local motor vehicle

• do not allow waves to break higher than 6 inches (15 cm) above thebottom edge of the rear bumper.Exceeding these limits may allow water to enter veh

Four Wheel Drive (4WD) vehicles:Tow your Four Wheel Drive vehicle with all four wheels on the ground orwith all four wheels off the ground using a veh

STARTINGPositions of the ignition1. Off— locks the gearshift leverand steering column and allows keyremoval.2. Accessory— allows the electricalaccesso

WARNING: If you smell exhaust fumes inside your vehicle, haveyour dealer inspect your vehicle immediately. Do not drive if yousmell exhaust fumes.Impo

• Make sure the gearshift is in P(Park).If starting a vehicle with a manualtransmission:• Make sure the parking brake isset.• Press and hold the clutc

Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrument Cluster chapter for more informationregarding the warning

Locks and Security 85Keys 85Locks 87Anti-theft system 98Seating and Safety Restraints 102Seating 102Safety restraints 113Airbags 127Child restraints 1

AUDIO SYSTEMSAM/FM/single CD or in-dash CD6/MP3 satellite compatible soundsystemWARNING: Driving while distracted can result in loss of vehiclecontrol

ENGINE BLOCK HEATER (IF EQUIPPED)An engine block heater warms the engine coolant which aids in startingand allows the heater/defroster system to respo

• Be sure that areas where the vehicle is parked are clean and clear ofall combustibles such as petroleum products, dust, rags, paper andsimilar items

Under normal operating conditions, brake dust may accumulate on thewheels. Some brake dust is inevitable as brakes wear and does notcontribute to brak

Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.ADVANCETR

WARNING: If a failure has been detected within theAdvanceTrac威 with RSC威 system, the ⬙sliding car⬙ iconwillilluminate steadily. Verify that the Advanc

When AdvanceTrac威 with RSC威 performs a normal system self-check,some drivers may notice a slight movement of the brake, and/or arumble, grunting, or g

Electronic Stability Control (ESC)Electronic Stability Control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa

Switching Off Traction ControlIf the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off the Traction Control features

WARNING: Trailer sway control does not prevent a trailer fromswaying, it mitigates the sway from increasing once it hasoccurred. TSC cannot stop all t

AM/FM Radio/ VOL (Power/Volume): Pressto turn the radio on/off. Turn theknob to increase/decrease volume.If the volume is set above a certainlevel and

STEERINGYour vehicle is equipped with an Electric Power-Assisted Steering(EPAS) system. There is no fluid reservoir to check or fill.If your vehicle l

WARNING: Vehicles with a higher center of gravity such asutility vehicles and trucks handle differently than vehicles with alower center of gravity. U

2. Using a screwdriver or similartool, carefully pry out the smallBrake Transmission Shift Interlock(BTSI) cover cap located to theright of the gearsh

Understanding the gearshift positions of the 6–speed automatictransmissionP (Park)This position locks the transmissionand prevents the front wheels fr

D (Drive) with Grade AssistPressing the transmission controlswitch on the side of the gearshiftlever activates Grade Assist andcancels Overdrive.• Pro

If your vehicle gets stuck in mud or snowIf your vehicle gets stuck in mud or snow, it may be rocked out byshifting between forward and reverse gears,

Do not drive with your foot resting on the clutch pedal or use theclutch pedal to hold your vehicle at a standstill while waiting on ahill. These acti

WARNING: Do not park your vehicle in Neutral, it may moveunexpectedly and injure someone. Use 1 (First) gear and set theparking brake fully.REVERSE SE

The RSS detects obstacles up to6 feet (1.8 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the

FOUR WHEEL DRIVE (4WD) SYSTEM (IF EQUIPPED)WARNING: For important information regarding safe operationof this type of vehicle, see Preparing to drive

To activate the autoset feature: Press MENU repeatedly until AUTOPRESET ON/OFF appears in the display. UseSEEK/TRACK totoggle AUTO PRESET to ON, and e

If your vehicle goes off the edge of the pavement• If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ea

WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your author

Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required f

Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should

Driving on snow and ice4WD vehicles have advantages over 2WD vehicles in snow and ice butcan skid like any other vehicle.Should you start to slide whi

Failure to maintain your vehicle properly may void the warranty, increaseyour repair cost, reduce vehicle performance and operational capabilitiesand

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co

FUEL PUMP SHUT-OFF SWITCHThis device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt.After an

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

To auto load up to six discs– Press and hold LOAD until the displayreads AUTOLOAD #. Load the desired disc, label side up. The systemwill prompt you t

The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Not used (spare)2 15A Brake On/Off switch3 15A Sync module4 30A

Fuse/RelayLocationFuse AmpRatingProtected Circuits16 15A Not used (spare)17 20A All lock motor feeds, Liftgaterelease, Liftglass release18 20A Heated

Fuse/RelayLocationFuse AmpRatingProtected Circuits41 15A Driver/passenger door lockswitches, Automatic dimmingmirror, Compass, Ambientlighting, Moon r

If the battery has been disconnected and reconnected, refer to theBattery section of the Maintenance and Specifications chapter.The high-current fuses

Fuse/RelayLocationFuse AmpRatingProtected Circuits13 10A* A/C clutch14 15A* Trailer tow turn lamps15 — Not used16 40A** Cooling fan 117 40A** Cooling

Fuse/RelayLocationFuse AmpRatingProtected Circuits31F — Liftgate latch relay32 — Not used33 — PCM diode34 — Start diode35 10A* Run/start, Reverse lamp

WARNING: Refer to Tire pressure monitoring system (TPMS)in the Tire, Wheels and Loading chapter for importantinformation. If the tire pressure monitor

Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following:• Handling, stability and braki

Stopping and securing the vehicle1. Park on a level surface, set theparking brake and activate hazardflashers.2. Place gearshift lever in P (Park)(aut

Remove the lug wrench from thejack in order to remove the sparetire from under the vehicle.Removing the spare tire or spare tire and tether (if equipp

In MP3 folder mode– Press DIRECT and the memory preset buttons(0–9) of the desired folder. The system will advance to that specificfolder.TEXT:In MP3

5. Use the lug wrench to remove thelug nut from the spare tire tether.6. If not replacing the spare or flattire to the underbody storage area,raise wi

WARNING: Do not attempt to change a tire on the side of thevehicle close to moving traffic. Pull far enough off the road toavoid the danger of being h

Before placing the jack under the vehicle, NOTE the jack locations:• FrontView shown from rear of front tire.Position the jack directly below theprotr

• RearView shown from forward of reartire. Position the jack directly belowthe stud on the rear trailing arm.3. Position the jack according to theguid

Never use the differentials as ajacking point.WARNING: To lessen therisk of personal injury, donot put any part of your bodyunder the vehicle while ch

Stowing the jack and tools• Make sure the jack is fullylowered.• Reclip the tools onto the jackmaking sure that the tools arefully contained by the cl

spare tire carrier has a built-in ratchet feature that will not allow you toovertighten. If the spare tire carrier ratchets with very little effort, t

Note: Inspect the wheel pilot holeprior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean r

Preparing your vehicleWhen the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

SEEK/TRACK: PressSEEK/TRACK to seek tothe previous/next channel. If aspecific category is selected, (Jazz,Rock, News, etc.), pressSEEK/TRACK to seek t

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

SATELLITE RADIO MENU: Press MENU when satellite radio mode isactive to access. Press OK to enter into the satellite radio menu.Press/ to cycle through

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio

ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro

To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is

WAXING• Wash the vehicle first.• Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your aut

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

3.0L V6 DURATEC ENGINEPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your aut

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32-A),available from your au

If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows:1. Wipe up spilled liqui

LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• For routine cleaning, wipe the surface wit

d. DISABLE ALERTS/ENABLE ALERTS: Press OK toenable/disable the satellite alert status which alerts you when yourselected songs are playing on a satell

Motorcraft Detail Wash (ZC-3-A)Motorcraft Dusting Cloth (ZC-24)Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20)Motorcraft Engine Shampoo (C

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

Working with the engine on• Automatic transmission:1. Set the parking brake and shift to P (Park).2. Block the wheels.• Manual transmission:1. Set the

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.5L I4 engine1. Engine coolant reservoir2. Engine oil filler cap3. Automatic transmission dipstick (i

3.0L V6 Duratec engine1. Engine coolant reservoir2. Air filter assembly3. Brake fluid reservoir4. Automatic transmission fluid dipstick5. Power distri

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

CHANGING THE WIPER BLADES1. Pull the wiper blade and armaway from the glass.2. Squeeze the locking tabs torelease the blade from the arm andpull the b

Changing rear window wiper bladeThe rear wiper arm is designed without a service position. This reducesthe risk of damage to the blade in an automatic

5. Locate and carefully remove the engine oil level dipstick.• 2.5L I4 engine• 3.0L V6 Duratec engine6. Wipe the dipstick clean. Insert the dipstick f

• 3.0L V6 Duratec engine• If required, add engine oil to the engine. Refer to Adding engine oilin this chapter.• Do not overfill the engine with oil.

FADE: Press SEEK/TRACK to adjust the audio between theback (B) and front (F) speakers.SPEED COMPENSATED VOLUME (if equipped): With this featureon, rad

Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by th

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

• Refer to scheduled maintenance information for service intervalschedules.• Be sure to read and understand Precautions when servicing yourvehicle in

• Do not add/mix an orange-colored, extended life coolant suchas Motorcraft Specialty Orange Engine Coolant, meeting Fordspecification WSS-M97B44-D, o

6. Fill the coolant reservoir slowly with the proper coolant mixture.7. Close the bleed valve when coolant begins to seep from it.8. Continue filling

• Increased engine coolant concentrations above 60% willdecrease the overheat protection characteristics of the enginecoolant and may cause engine dam

When this occurs the vehicle will still operate. However:• The engine power will be limited.• The air conditioning system will be disabled.Continued o

WARNING: The fuel system may be under pressure. If you heara hissing sound near the fuel filler door (Easy Fuel™ “no cap”fuel system), do not refuel u

Auxiliary input jack (Line in)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends th

• Be particularly careful if you are taking “Antabuse” or other forms ofdisulfiram for the treatment of alcoholism. Breathing gasoline vapors,or skin

Easy Fuel™ “no cap” fuel systemYour fuel tank is equipped with an Easy Fuel™ “no cap” fuel fillersystem. This allows you to simply open the fuel fille

WARNING: The fuel system may be under pressure. If you heara hissing sound near the fuel filler door (Easy Fuel™ “no cap”fuel system), do not refuel u

Fuel qualityIf you are experiencing starting, rough idle or hesitation driveabilityproblems, try a different brand of unleaded gasoline. “Premium”unle

Refilling with a portable fuel containerWith the Easy Fuel™ “no cap” fuel system, use the following directionswhen filling from a portable fuel contai

4. When done, clean the funnel or properly dispose of it. Extra funnelscan be purchased from your authorized dealer if you choose to disposeof the fun

• Use the same side of the same pump and have the vehicle facing thesame direction each time you fill up.• Have the vehicle loading and distribution t

• Slow down gradually.• Driving at reasonable speeds (traveling at 55 mph [88 km/h] uses 15%less fuel than traveling at 65 mph [105 km/h]).• Revving t

• Transmissions give their best fuel economy when operated in the topcruise gear and with steady pressure on the gas pedal.• Close windows for high sp

An improperly operating or damaged exhaust system may allow exhaustto enter the vehicle. Have a damaged or improperly operating exhaustsystem inspecte

Customer Assistance 255Reporting safety defects (U.S. only) 261Reporting safety defects (Canada only) 262Cleaning 263Maintenance and Specifications 27

4. Turn the radio on, using either a tuned FM station or a CD loaded intothe system. Adjust the volume to a comfortable listening level.5. Turn the po

If the service engine soon indicator remains on, have your vehicleserviced at the first available opportunity. Although some malfunctionsdetected by t

BRAKE/CLUTCH FLUIDBrake and clutch systems are supplied from the same reservoir.The fluid level will drop slowly asthe brakes wear, and will rise when

6. Install the dipstick making sure it is fully seated in the filler tube.7. Remove the dipstick and inspect the fluid level. The fluid should be inth

Use of a non-approved automatic transmission fluid may causeinternal transmission component damage.If necessary, add fluid in 1/2 pint (250 ml) increm

WARNING: To reduce the risk of vehicle damage and/orpersonal burn injuries do not start your engine with the aircleaner removed and do not remove it w

MOTORCRAFT PART NUMBERSComponent 2.5L I4 engine 3.0L V6 Duratec engineAir filter element1FA-1683 FA-1683Battery BXT-40R BXT-40ROil filter FL-910 or FL

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord part name orequivalentFord part number /Ford SpecificationBrake fluid and (clutchfl

Item CapacityFord part name orequivalentFord part number /Ford SpecificationEngine oil2.5L engine5.3 quarts(5.0L)Motorcraft SAE 5W-20Premium Synthetic

Item CapacityFord part name orequivalentFord part number /Ford SpecificationFuel tank16.5 gallons(62.5L)——1Add the coolant type originally equipped in

ENGINE DATAEngine 2.5L I4 engine3.0L DOHC V6 DuratecengineCubic inches 152 183Required fuel 87 octane 87 octaneFiring order 1-3-4-2 1-4-2-5-3-6Ignitio

Your vehicle may be equipped with aUSB port located on the instrumentpanel. This feature allows you toplug in media playing devices,memory sticks, and

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

LifestyleAsh cup/ smoker’s packageCargo management accessoriesCross barsTrailer hitches, wiring harnesses and accessoriesPeace of mindMobile-Ease™ han

AAccessory delay ...64AdvanceTrac ...204Air cleaner filter ...303, 305Air conditioningau

LATCH ...150recommendations ...144Child safety seats - boosterseats ...

lubrication specifications ...306refill capacities ...306service points ...273–274starting after a collision .

Inspection/maintenance (I/M)testing ...300Instrument panelcleaning ...267cluster

Parts (see Motorcraft parts) ...305Passenger OccupantClassification Sensor ...114Power distribution box(see Fuses) ...

Special noticeambulance conversions ...8utility-type vehicles ...8Specification chart,lubricants ...

CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C

Windshield washer fluid andwipers...57checking and adding fluid...275liftgate reservoir ...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requiresmore than twoseconds to produceaudio for theselected channel.No action required. Thisme

Radio Display Condition Action RequiredNO TEXT Categoryinformation notavailable.Category information notavailable at this time on thischannel. The sys

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1.Fan speed adjustment: Turn to select fan speed.2.RRear defroster: Press to activate/deactivat

9. Temperature control: Controls the temperature of the airflow in thevehicle.10.Passenger heated seat control (if equipped): Press toactivate/deactiv

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

Operating tips• To reduce fog build up on the windshield during humid weather,select(defrost) or (floor/defrost).• To reduce humidity build up inside

DUAL AUTOMATIC TEMPERATURE CONTROL (IF EQUIPPED)1. AUTO/Driver temperature: Press to engage full automaticoperation. Select the desired temperature us

5. Power/ : Press to activate/deactivate the climate controlsystem. When the system is off, outside air is prevented from enteringthe vehicle through

14. Driver heated seat control (if equipped): Press toactivate/deactivate the driver heated seat. See Heated seats in theSeating and Safety Restraints

4. Set the temperature to 60°F (16°C).5. Set highest fan setting initially, then adjust to maintain comfort.To aid in side window defogging/demisting

HEADLAMP CONTROLRotate the headlamp control to thefirst position to turn on theparking lamps.Rotate to the second positiontoturn on the headlamps.Rota

Autolamp delay system (if equipped)If your vehicle is equipped with autolamps, you can set the delay time tokeep the headlights on for up to three min

Flash to passPull toward you slightly to activateand release to deactivate.Daytime running lamps (DRL) (if equipped)Turns the lowbeam headlamps on wit

Note: If the battery is disconnected, discharged, or a new battery isinstalled, the dimmer switch requires re-calibration. Rotate the dimmerswitch fro

5. Locate the vertical adjuster onthe headlamp, then turn theadjuster either clockwise (to adjustup) or counterclockwise (to adjustdown) aligning the

Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti

• ON: In this position, the lamp will remain illuminated.The map lamp controls (withoutmoon roof) are located on the domelamp. Press the button on eit

Note: The ambient lights will stay on until the ignition is placed in theoff position and either of the front doors are opened or the accessorydelay t

Function Number of bulbs Trade numberHeadlamps (high andlow beams)2H13Park/turn lamps(front)23157A (amber)Side marker (front) 2 194Rearstop/tail/sidem

5. Disconnect the electricalconnector from the bulb.WARNING: Handle ahalogen headlamp bulbcarefully and keep out ofchildren’s reach. Grasp the bulbonl

Replacing front sidemarker bulbsFor bulb replacement, see your authorized dealer.Replacing tail/stop/turn/backup lamp bulbsThe tail/stop/turn/sidemark

2. Remove the bulb holder from thelamp assembly by pressing thesnaps.3. Pull the bulb straight out of thesocket and push in the new bulb.Install the n

Replacing fog lamp bulbs (if equipped)1. Make sure the fog lamp switch isin the off position.2. From underneath the vehicle,carefully disconnect the e

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Rear window wiper/washer controlsFor rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select:2 — Normal spe

ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamps.OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehi

Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance

Most geographic areas (zones) have a magnetic north compass point thatvaries slightly from the northerly direction on maps. This variation is fourdegr

Compass calibration adjustmentPerform compass calibration in an open area free from steel structuresand high voltage lines. For optimum calibration, t

The tray and inside bin can beremoved to open up space to fit alaptop computer, MP3 players, CDsor handbags. To remove, open theconsole lid and pull t

The auxiliary power point is locatedin the instrument panel.A second auxiliary power point islocated on the rear side of thecenter console.Do not use

WARNING: When closing the power windows, you should verifythey are free of obstructions and ensure that children and/orpets are not in the proximity o

INTERIOR MIRRORThe interior rear view mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side.

To adjust your mirrors:1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror.2. Mo

Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas

Resuming a set speedPress the RES control and releaseit. This will automatically return thevehicle to the previously set speed.Increasing speed while

Turning off speed controlThere are two ways to turn off thespeed control:• Press the OFF control.• Turn off the ignition.Note: When you turn off the s

Event Data RecordingOther modules in your vehicle — event data recorders — arecapable of collecting and storing data during a crash or nearcrash event

In any mode:• Press VOL + or VOL - to adjustthe volume.Navigation system hands freecontrol features (if equipped)Press and holdcontrol brieflyuntil th

Navigation system/SYNC威 handsfree control features (ifequipped)Presscontrol briefly until thevoiceicon appears on theNavigation display to use the voi

Bounce-back: When an obstacle has been detected in the moon roofopening as the moon roof is closing, the moon roof will automaticallyopen and stop at

Selectable featuresResetPress this control to select and resetfunctions shown in the INFO menuand SETUP menu.Info menuThis control displays the follow

If you calculate your average fuel economy by dividing miles traveled bygallons of fuel used (liters of fuel used by 100 kilometers traveled), yourfig

• Language• Compass Zone/Compass calibration (if equipped)Reset to English (if in another language)When entering the SETUP MENUand a non-English langu

Oil lifeAn oil change is required whenever indicated by the message center.USE ONLY RECOMMENDED ENGINE OILS.To reset the oil monitoring system to 100%

2. Press the RESET control to select the new Autolamp delay values of0, 10, 20, 30, 60, 90, 120 or 180 seconds.AutolockThis feature automatically lock

In the event of a multiple warning situation, the message center willcycle the display to show all warnings by displaying each one for fourseconds.The

REAR RIGHT DOOR AJAR — Displayed when the rear right door isnot completely closed.PARK BRAKE ENGAGED — Displayed when the manual park brake isset, the

Notice to owners of pickup trucks and utility type vehiclesWARNING: Utility vehicles have a significantly higher rolloverrate than other types of vehi

LIFTGATE• To open the liftgate window,unlock the liftgate (with thepower door locks or the remoteentry) and push the right sidecontrol button under th

To install the shade:• Insert the ends of the cargoshade into the mounting featureslocated behind the rear seat onthe rear trim panels.To operate the

2. The smaller compartment contains the jack kit. There is also extrastorage space for customer use. The lid on the small compartment isaccessible and

To remove the cross-bar assembly (if equipped) from the roof rackside rails:1. Loosen the thumbwheel at bothends of the cross-bar (bothcross-bars are

To reinstall the cross-bar assembly (if equipped) to the roof rackside rails:1. Ensure that both cross-barassemblies are installed with the F(front) a

KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unl

Recommended handling of the Integrated Keyhead Transmitter(IKT)To avoid inadvertently activating the remote entry functions of yourvehicle, it is reco

POWER DOOR LOCKS• Press thecontrol to unlock alldoors.• Press thecontrol to lock alldoors.Door key unlocking/lockingUnlocking the doorsTurn the key in

Note: The autolock feature can be activated/deactivated independentlyof the autounlock feature.Before following the activation or deactivation procedu

Message center procedureFor information on activating/deactivating the autolock feature using thevehicle’s message center, refer to Message center inf

Export unique (Non–United States/Canada) vehicle specificinformationFor your particular global region, your vehicle may be equipped withfeatures and o

1. Place the key in the ignition andturn the ignition to the on position.2. Press the power door unlockcontrol on the door panel threetimes.3. Turn th

CHILDPROOF DOOR LOCKSWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo

The IKT allows you to:• remotely unlock the vehicledoors.• remotely lock all the vehicledoors.• remotely open the power liftgateglass.• activate the p

Locking the doors1. Press and release to lock all the doors. Assuming all vehicle doorsand the liftgate are properly closed, the park/turn lamps will

To replace the battery:1. Twist a thin coin in the slot of theIKT near the key ring in order toremove the battery cover.Note: Do not wipe off any grea

The illuminated entry system will turn off the interior lights if:• the ignition is turned to the on position, or• the Integrated Keyhead Transmitter

1. The ignition must be off to beginthe sequence.2. Place the key in the ignition andturn the ignition to the 3 (on)position.3. Press the power door u

When pressing the controls on the keyless entry keypad, press themiddle of the controls to ensure a good activation.Programming your own personal entr

Unlocking and locking the doors and liftgate using keyless entryTo unlock the driver’s door, enter the factory set 5-digit code or yourpersonal code.

Anti-theft indicatorThe anti-theft indicator is located in the instrument panel cluster.• When the ignition is in the offposition, the indicator will